how to fill a hole in a pontoon floor

How to Repair a Damaged Pontoon | Gone Outdoors | Your ...pontoon boats maintain their buoyancy by means of air-filled aluminum pontoons placed beneath the deck. These types of boats are great for those looking for a low ... Remove the patch. Drill holes into the pontoon at the markings. 6. Coat the repair area on the pontoon with the epoxy solution. allow this to dry, if needed, according to the manufacturer's instructions. 7. apply the epoxy sealant to the inside of the aluminum patch. 8. Set the aluminum patch over the repair area, making ...

DIY Repairing a Hole or Crack in an Aluminum Boat SUPER EASY ...12 apr 2016 ... I you have a hole, crack or leaky rivet it is super easy to fix on your own with a small propane torch and some HTS-735-11 rods. i have seen people use JB Weld or other epoxies and even that spray on rubber leak fixer and all them are great temporary fixes. If you want a more permeant fix get some HTS-735-11. The HTS-735-11is a flux less rod that works like a brazing rod or soldering. If you can light a torch and use a pencil you can fix your boat.

Cheap fix for a rotten boat floor (Part 1 of 2) Installing new plywood ...18 Jul 2015 ... DescriptionThis DIY video shows how to fix a rotten boat floor. The text book way of replacing the floor is to remove the consoles, seat boxes and remove all the original plywood floor. Then replace the stringers underneath. Then fibreglass the stringers into the hull. Then replace the plywood floor. Then fiberglass the floor. That is a MaJOR job and only worth doing on a boat that has sentimental or major financial value when the restoration is complete. This boat is not ...

4 Mistakes to Avoid When Repairing a Rotting Boat Floor ...Replacing a piece of rotting floor is the best course of action because there is no telling how bad the rotting is as it could have spread to other places not immediately visible; however, if you have no choice but to patch the rotten section, it is better ... Doing this simple additional task will save you a lot of time and money down the line, since the putty or epoxy will effectively cover the hole created by the head of the nail. ... The best thing you can do when fixing a boat floor is to use epoxy.

How To: Find and Fix Inflatable Boat Valve Leaks - YouTube21 Nov 2011 ... Finding and fixing leaks in the valves on your inflatable raft, cataraft or inflatable kayak (IK) is an important skill for boaters. Here NRS repair guru Jos...

Repairing a Runabout Floor or Pontoon Deck - Epoxyworks31 Jul 2014 ... Repairing a Runabout floor or pontoon Deck. By Joe Parker. a common source of ... On runabouts, the floor is usually tabbed or joined to the hull sides with fiberglass tape at the edges of the plywood and up the side of the hull a few inches. Some runabouts will also have a layer or two ... Cut through the fiberglass at the floor/hull joint if the plywood is tabbed to the hull with fiberglass tape or if the floor is covered with a layer of glass. Remember that this is not a 90° ...

How To: Inflatable Repair Adhesives Guide - YouTube17 Dec 2012 ... When repairing your Hypalon , PVC or urethane inflatable, or your plastic or composite kayak, it's vital that you choose the right adhesive and solvent for t... ... I have a one person pontoon boat with 9' pontoons it has a nylon outer cover but it looking a little dengey. I tryed cleaning it. But still looking bad. ... Right in the corner so he basically created a hole and connected the air supply that was separated from the sides of the boat to the floor. Is this a lost project?.

Pontoon Buyer's Guide - Boatland IncThis stress can tear a pontoon apart over time if the proper fasteners are not utilized. Some manufacturers choose to bolt their decking to the cross-channel instead of utilizing self-tapping screws. in theory, this sounds like a superior attachment technique, although the disadvantage to this approach is that in order to install the bolts, they must pre-drill a hole slightly larger than the bolt they plan to use. Due to the stress mentioned above, over time, this could create a wallowing effect ...

New Life for an Old Pontoon Boat | Tropical Boating28 Jul 2014 ... pontoon boat deck damage Deck Damage. The results of removing the old console supports are shown at right. I think I used 3M 4200 and it really stuck to that plywood! I was able to cut and pry most of it away, but some pretty good sized pieces of the plywood deck came up too. Fuel Tank Mounting holes. as long as I was into deck repair mode, I decided to fill the old fuel tank mounting holes and drill some oversized new ones to fill with epoxy. While I was at it, I filled ...

Replacing boat carpet on a pontoon | Boat Carpet Buys18 Sep 2013 ... The first segment in our series on "how to Replace Boat Carpet" will focus on replacing carpet on a pontoon boat. Of the many types of boats that need carpeting. ... If you are not replacing the plywood you will be able to locate the holes in your deck but take lots of pictures during this step of the carpet replacement process so you know how to put everything back on your boat. You also need to remove the deck trim pieces that are attached to the side of the deck in ...

Leaking Pontoon House Boats - How to Find and Repair a Leak?If not, you can also use an air compressor to fill the pontoons with pressure to listen for a hissing so

How To EASILY Repair Holes In Aluminum - YouTube22 Jul 2014 ... Learn how simple it is to repair holes in aluminum plates and pots using a quality aluminum brazing rod like alumite brand. Using a clean stainless steel bru...

The Pros and Cons of Popular Pontoon Boat Decking Materials and ...30 Jun 2017 ... pontoon boat decking gives you so many choices: sizes, materials, covering. Here's what you need to ... That's why I recommend that every pontoon owner learn about the deck of their boat, as well as how to protect, maintain, repair and replace iteven those of us who are less savvy about mechanical things. above board ... Self-tapping screws Screws create strong attachments and are inserted through self-supported holes (that don't require pre-drilling). That can ...

Fixing Holes in an Aluminum Boat - YouTube7 Jan 2013 ... This video shows a technique of repairing holes in an aluminum boat which works for holes up to 1/4" in diameter. Full instructions below. Please, feel free ...

Wood preservation, rot repair, and restoration ... - secure.rotdoctor.comOne of the most common areas of damage on fiberglass and pontoon boats is deteriorated or rotted-out cockpit/deck flooring. The reasons are obvious: water saturation through leaking glass laminate and plywood. Sometimes this can be repaired by treating the existing wood or by drilling access holes in the glass laminate and injecting CPES (Clear Penetrating Epoxy Sealer) and, if the damage is severe, Layup & Laminating Resin. We cover this process under Deck Repair in a ...